There can technically be two different wheel bearing kits for 5,200 pound axles. They will use different outer bearings and grease seals, so I highly suggest pulling one of the hubs off to verify which you need.
The first kit, # BK3-300, uses a grease seal with an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This also uses the outer bearing # LM67048, which has a 1.25 inch inner diameter.
The other kit, # BK3-310, uses a grease seal with an inner diameter of 2.125... view full answer...
For your RVP 7000 / 8000 series AC on your 2002 Keystone Hornet you can use the Replacement RV Air Conditioner Cover for MaxxAir Units # MA8335A5261 for a replacement shroud. view full answer...
Yes, the Replacement Lead Leg # LC119102 is the correct leg for your VMC900R Venture Landing Gear on your 2009 Keystone Cougar 5th wheel.
The Replacement Follow Leg # LC119101 is also available if you would like to replace the follow leg as well on your Cougar.
The Ultra-Fab Spring-Loaded Quick Pins # UF17-943031 are replacements for your current pins as the new legs only include a snapper pin. view full answer...
The Replacement T-Handles for JT's Strong Arm Jack Stabilizer Kits - Qty 2 # LC314594. The outer sleeve you are seeking is Replacement Outer Stabilizer for JT's Strong Arm Jack Stabilizer - 1-1/4" OD - Qty 1 # LC191014. view full answer...
Your 2022 Keystone Cougar 316RLS does have a Lippert 1621 Pin Box # LC1191191. You are able to upgrade this to one of the following pin boxes.
MORryde Cushioned 5th Wheel Pin Box # MR84VR
Trailair Rota-Flex 5th Wheel Pin Box # LC328330
Curt Flex Air 5th Wheel Pin Box # LC328492
If you are looking to use with a gooseneck hitch we have the Gen-Y Hitch 5th Wheel to Gooseneck Pin Box # GY58GR. Do remember you will need the Safety Chains # GY49GR if you are going to the ball connection. view full answer...
I spoke with Lippert and confirmed that the 18:1 Tuson Motor # LC125802 would be the correct replacement for the slide out motor in your 2007 Keystone Cougar fifth wheel. Thank you for the info and picture you sent over! view full answer...
It sounds like the compressor is bad and you'll need to replace the unit. I recommend getting the Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor - 15,000 Btu - White # ACDOM150. This will directly fit your current wiring for an easy swap with no changes required on the inside of the trailer. view full answer...
I really like the Timbren Silent Ride systems like part # TSR14KT01 that is rated for 3" axles and 14,000 lbs. This gets rid of the traditional leaf spring setup and gives you pivoting arms and Double Aeon rubber springs for a better ride quality. The mounting bracket bolts to your trailer frame and is for 33" wheelbase applications.
If this matches your Keystone I'd say go for it, otherwise let me know your wheelbase (center axle to center axle) and I can see if we have one that will... view full answer...
The Replacement Motor for Stromberg Carlson Electric Landing Gear Set part # LG-196308 is likely the replacement you need. It is designed to fit a wide variety of landing gear sets out there and the Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear part # LG-179015 is the correct gearbox for the motor.
It sounds to me as if it is in the motor rather than in the gearbox because of the fact it reset for a while before fully failing. I would start there and get the gearbox if... view full answer...
It sounds like you are looking for a replacement hydraulic cylinder for a slide-out. If that is the case then the closest match we have to the information provided is the Lippert Replacement Hydraulic Cylinder for RV Slide-Out part # LC42FR which measures 41-5/8" long. view full answer...
In order to determine the correct replacement shackle links for your Keystone 5th Wheel Trailer, you will want to measure both the length and hole diameter on your existing parts. Unfortunately, trailer manufacturers do not typically keep record of smaller parts like suspension components that were installed at the factory. Finding a replacement that matches the dimensions on your current shackle is the best and most accurate method.
I have attached a link that will take you to our available... view full answer...
The Replacement Touchscreen Remote w/ Charger for Lippert Ground Control 3.0 Electric Leveling System part # LC358601 is only for use with the Ground Control 3.0 System. For a remote that works the other electronics the Replacement New-Style Linc Analog Remote part # LC292614 is what you are looking for.
I have linked the pairing process in the attached photo for you to check out. view full answer...
We are currently only going to have center caps like the Lionshead # LHCS108-SI60C which fits the common 4.25 pilot hole found on 16" wheels like you have on your 2021 Keystone Cougar 316RLS 5th wheel. These have the smaller snap in cap than those that would have come from Keystone. If you want to have an exact match you would have to order replacements from Keystone. view full answer...
You can replace the Equa-Flex with the Road Armor # LC696740 as long as you currently have the # LC279687. This Equa-Flex model measures 5-1/2" between left and right bolt holes and the Road Armor measures 6". This won't be too much of a difference.
However, if you have a model like # LC279688 with 7-1/2" spacing the difference will be too much to use the Road Armor as a replacement. If that is the case, you will want to either replace it with another Equa-Flex or you could switch to... view full answer...
I can certainly point you in the right direction. The Dometic Duo Therm 3107541.009 is a model that we see fairly frequently. Now I do not have literature on your specific camper that will tell me if it is ducted or ductless, but the Advent units we offer are compatible with both setups.
I recommend for you the Advent Air # ACDOM150. This is made to be compatible with your current Dometic setup, so you will not have to change out anything inside the camper. You will be able to use your... view full answer...
Yes, the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00 is the correct part for your 6504-414. This kit replaces the bow-tie bracket, motor, and blade for your Fan-Tastic Vent roof vent fan. Since the fan stopped working and is now out of production, you may also want to consider a total replacement.
If you decide to completely replace the fan I recommend the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 14-1/4" x 14-1/4" # FV802250... view full answer...
For the Stromberg Carlson Electric Landing Gear Set we have the Replacement Motor, # LG-142178 that is designed for use with Stromberg Carlson model LG-1 or LG-2. This has a weight capacity of 5,500 lbs. and a motor speed of 5,500 rpm's. The Replacement Motor, # LG-196308 is for use with Stromberg Carlson model LG-3 or LG-4 models and has a weight capacity of 6,500 lbs. and a motor speed of 5,430 rpm's.
Please compare these to the replacement motor you used for options of a larger capacity.... view full answer...
The Keystone Montana's use a unique custom landing gear system from Lippert, the correct replacement lead leg for that landing gear system is the Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653. view full answer...
Currently the LED RV Security Light # CE76FR is the only 12 volt powered motion activated light that we have that would work for your 2020 Keystone Cougar 268MBI in your entry way.
While it does not have a switch you could add a Mini-12V Switch # 37212785 next to it or your existing light to allow you to switch it on and off. view full answer...
The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part # LC136046 and part # LC118246 are the same solenoid but vary in how they mount. The part # LC136046 mounts using a strap around the motor like what you have therefore this is the correct replacement for you whereas the part # LC118246 mounts on a tray beside the motor. view full answer...
Go To Results